FAQ
Liqstech fixes leaks in minutes without infrastructure damage!

Definitely yes.

Liqstech's revolutionary liquid has been tested and approved for use in drinking water piping by the Israeli Standards Institute (testing certificate of the Israeli Standards Institute No. 7312205903)

In order to prevent damage to the infrastructure of the plumbing system, only a plumber who has undergone training on behalf of Liqstech and received approval for purchase and use, is authorized to use the liquid sealant to repair leaks.

Definitely yes!

​Liqstech has been tested and found to be suitable for sealing leaky connectors of all types and in hot water piping in addition to cold.

• In pipes with a diameter of 16-20 mm, Liqstech seals holes up to a diameter of 1.5 mm

• In pipes with a diameter of 25-32 mm, Liqstech seals holes up to a diameter of 2 mm

The Liqstech liquid sealant is an effective and long-lasting solution for 80% of cases in water pipe leaks. Before use, it is mandatory to read the information sheet.

• In a 16 mm diameter pipe (cold water) and up to 20 meters in length, an amount of 1 liter (1 bottle) must be used to seal a hole up to a maximum diameter of 1.5 mm.
   

• In a 20 mm diameter pipe (cold water) and up to 20 meters in length, for sealing a hole up to a maximum diameter of 1.5 mm, an amount of 1 liter (1 bottle) must be used. In cases where the pipe is longer than 20 m, an amount of 2 liters (2 bottles) must be used.
   

• In a 25mm diameter pipe (cold water) and up to 20 meters in length, for sealing a hole up to a maximum diameter of 2 mm, an amount of 1 liter (1 bottle) must be used. In cases where the pipe is longer than 20 m, an amount of 2 liters (2 bottles) must be used.
   

• In a 32mm diameter pipe (cold water) and up to 15 meters in length, for sealing a hole up to a maximum diameter of 2 mm, an amount of 1 liter (1 bottle) must be used. In cases where the pipe is longer than 15 m, an amount of 2 liters (2 bottles) must be used.

Definitely yes!

​Liqstech has been tested and found to be suitable for sealing leaky connectors of all types and in hot water piping in addition to cold.

Not currently!
But if the source of the leak comes from a connector located in a hot water pipe, you can apply the Liqstech sealant by flushing it with cold water only.

In rusty iron pipes, there is a great risk of the pipe being blocked by the material, and therefore, it is mandatory to clean the rusty pipe before starting the repair.

Yes, for the reason that the professional is responsible for the quality of the repair, and if at a later time a leakage problem arises at another location in the pipe, the plumber must know that this is a new, or different leak that is not related to the successful repair of his previous work.

Not at all, but it consists of several simple steps:

• Locating and isolating the leaking pipe from the water system.

• Disconnecting the pipe from the water clock.

• Purring the Liqstech sealant into the damaged pipe.

• Waiting for 30 minutes while maintaining a maximum water pressure of 4.5 bar.

• Flushing the system with clean water, and connecting the pipe back to the water clock.

Definitely yes!
For example, when the Liqstech sealant is fed into a16mm pipe and this pipe is connected to a 25mm pipe that is connected to a 16mm pipe again, the material will work perfectly.

If the material is runed through a 16 or 20 mm pipes, and the final exit is made through a 16 mm pipe, you must use a bottle adapted to a 16mm pipe only,
That is, the diameter of the outlet pipe determines with which type of bottle the repair is performed.